Browsing School of Engineering and Sustainable Development by Title
Now showing items 1-20 of 1946
-
A 2d-Numerical Study on Slot Jet Applied to a Wind Turbine as a Circulation Control Technique
(Conference)A study on the feasibility of the Circulation Control (CC) technique for wind turbines is proposed. The CC was born in aeronautic field to improve the lift force on the wings, allowing the short take-off and landing ... -
3-D Printing of Flexible Two Terminal Electronic Memory Devices
(Article)Recent strategy in the electronics sector is to ascertain the ways to make cheap, flexible and environmentally friendly electronic devices. The 3D inkjet printing technology is based on the Additive Manufacturing concept ... -
A 3D GBSM for high-speed train communication systems under deep cutting scenarios
(Conference)This paper proposes a novel three-dimensional (3D) cylinder geometry-based stochastic model (GBSM) for non-isotropic multiple-input multiple-output (MIMO) Rice fading channels in high-speed train (HST) wireless communications ... -
3D Model of partial discharge in defects with different sizes and positions in power cable for distribution and transmission networks
(Article)The knowledge of partial discharge (PD) phenomena inside electrical insulation of power cables is an important issue for assessing the insulation condition and its degradation state, obtaining information about the ... -
3D printing of bone scaffolds with hybrid biomaterials
(Article)In this research, a novel hybrid material bone implant manufacturing through the integration of two materials using additive manufacturing (AM) technology is proposed. Biomimetic application can manufacture high strength ... -
3D Printing of Flexible Two Terminal Electronic Memory Devices
(Conference)Recent strategy in the electronics sector is to ascertain the ways to make cheap, flexible and environmentally friendly electronic devices. The 3D Inkjet printing technology is based on the Additive Manufacturing concept ... -
3D printing of PEEK-based medical devices
(Article)Polyether-ether-ketone (PEEK) is an excellent thermoplastic alternative to metallic biomaterials which is used for loadbearing applications due to its high strength and stiffness, and biocompatibility with no cytotoxic ... -
3D printing of PEEK–cHAp scaffold for medical bone implant
(Article)The major drawback associated with PEEK implants is their biologically inert surface, which caused unsatisfactory cellular response and poor adhesion between the implants and surrounding soft tissues against proper bone ... -
3D printing of surface characterisation and finite element analysis improvement of PEEK-HAP-GO in bone implant
(Article)Research and development of polyetheretherketone (PEEK) composites with high thermal conductivities and ideal thermal stabilities have become one of the hot topics in composites. However, not all PEEK composites have the ... -
3D Simulation of Partial Discharge in High Voltage Power Networks
(Conference)Partial discharge (PD) events arise inside power cables due to defects of cable’s insulation material, characterized by a lower electrical breakdown strength than the surrounding dielectric material. These electrical ... -
5 million lux meters
(Conference) -
Abrupt fault remaining useful life estimation using measurements from a reciprocating compressor valve failure
(Article)One of the major targets in industry is minimisation of downtime and cost, and maximisation of availability and safety, with maintenance considered a key aspect in achieving this objective. The concept of Condition Based ... -
Accelerating lean practice training using virtual reality.
(Conference) -
Acceptability of Externally Controlled Recharging for the Protection of Local Power Networks with High Penetrations of Electric Vehicles
(Article)The anticipated uptake of electric vehicles (EVs) has the potential to overload low-voltage power networks where several EVs might be simultaneously recharging on the same electrical substation feeder. The Esprit system ... -
Acceptance of thermal conditions and energy use of three ventilation strategies with six exhaust configurations for the classroom
(Article)The paper describes an experimental study from forty-eight subjects about the acceptable thermal conditions under three ventilation strategies with six exhaust configurations, including mixing ventilation (MV), displacement ... -
Accommodating renewable generation through an aggregator-focused method for inducing demand side response from electricity consumers
(Article)The ability to influence electricity demand from domestic and small business consumers so that it can be matched to intermittent renewable generation and distribution network constraints is a key capability of a smart grid. ... -
Accuracy-Complexity Tradeoff Analysis and Complexity Reduction Methods for Non-Stationary IMT-A MIMO Channel Models
(Article)High-mobility wireless communication systems have attracted growing interests in recent years. For the deployment of these systems, one fundamental work is to build accurate and efficient channel models. In high-mobility ...